Do It Yourself Bathtub Setup.
Do It Yourself Bathtub Setup.
Blog Article
The writer is making a number of good pointers on Installing A Bathtub in general in the article down the page.
Setting up a bath tub isn't exactly brain surgery, yet it does need strong plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately tough task. If the old tub is easily accessible, the job can relocate speedily; if you have to open up a wall to eliminate the old bathtub and also position the brand-new tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to leave the old tub as well as embeded in the brand-new one. Ensure you have certified yourself for the job as well as fit attempting it. As opposed to hiring a service provider to take over a halfway-completed task, it is better to consider utilizing one prior to you begin. Chances are you might require a professional plumber to make tube links.
This post will assist you mount a new tub in your washroom if you have already acquired a new tub as well as do not need to alter the arrangement of your previous water pipes.
Your devices as well as product checklist need to comprise the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of eliminating the existing faucets can be fairly problematic due to the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old securing compound.
Before moving on to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washers remain in location in between the tap and also the sink. Protect the tap in position with the maker provided backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The former kind ought to be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Using both wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the spirit level as well as adjusting the feet on the tub up until the level reads degree.
To install taps, fit all-time low of the furthest versatile faucet connector to the suitable supply pipe by making a compression sign up with; then do the same for the other faucet.
Switch on the water supply and inspect all joints and new pipework for leaks as well as tighten them if required. Load the tub and additionally check the overflow electrical outlet as well as the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the bathtub ought to wait up until the tub has actually been made use of at the very least once as this will settle it right into its last placement.
Preparing for the Installation
First of all, the sustaining framework provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its last setting.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, causing the water to pass through the wall in between the bathroom as well as the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components as well as installations. They are offered in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to always fill up the tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can fracture fairly very early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently readily available on the market. It is suggested to fit the tiles utilizing water-resistant or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader about Tools You Need to Install a New Bathtub , I figured sharing that piece was worth the trouble. Enjoyed our content? Please share it. Help other people find it. Kudos for your time. Please pay a visit to our site back soon.
Quote Report this page